1 INSTALLATION MANUAL AND USER’S GUIDE Revision 5.8 Patent Pending www.ActiveForever.com
10 !!! WARNING !!! THE POWER ADAPTER MUST BE SCREWED DOWN TO PREVENT THE ADAPTER FROM BEING ACCIDENTALLY UNPLUGGED. THIS ADAPTER IS HEAVY AND CAN
11 The Autocloser must be mounted in a position with the infrared sensors aimed straight to-ward the reflector (Fig. 3-2). In order to accomplish th
12 Determine your mounting location by holding the Autocloser unit against the garage door opener power head assembly with the infrared sensor facing
13 5. Wire the Autocloser to the garage door opener. Read your garage door opener manual to determine where the wall button terminals are located on
14 6. Wire the disable button to the Autocloser. Locate the disable button next to the ga-rage door opener wall button. Attach one end of each wire,
15 7. Test the Autocloser system. Plug in the garage door opener. A. Switch the system to on. Close then reopen the garage door. As soon as the doo
16 !!!WARNIN STAY AWAY FROM THE DOOR WHILE IT IS CLOSING - THE GA-RAGE DOOR CAN CAUSE SEVERE INJURY!!! When the timer finishes it’s count, the syst
17 Fig. 8INSTALLATION OF OPTIONAL I-opener subsystem HARDWARE The I-opener subsystem can be installed anytime after the Autocloser-GA has been in-sta
18 10. Drill holes for the I-Opener terminal plate. Position the back of the terminal in the hole. Mark the terminal plate holes
19 12. Wire the I-Opener terminal to the Autocloser. Run the wire from the I-Opener terminal to the Autocloser unit attaching the wire to the wall
2 Autocloser is designed and manufactured by NOTE: This equipment has been tested and found to comply with the limits for a Clas
20 13. Insure that nobody is standing under the garage door. Plug the garage door opener back into its 110 Volt household receptacle. 14. Prog
21 OPERATION AND PROGRAMMING The Autocloser system is ready to operate straight out of the box. Once installed, the unit will automatically close yo
22 TIP- The auto close cancel feature can be used whenever the Autocloser begins its continuous warning beeps. 4) Set the auto close delay time - T
23 The unit does not beep or beeps intermit-tently when aligning the reflector while in setup mode STEP 1 1) Make sure the switch is
24 STEP 4 ?Press and release the Disable button while the unit is on. Does the unit beep twice? No- Go to Step 1 and re-align the refl
25 7) Unit begins to beep? Yes- Unit is working. Fol-low all installation steps. No– please contact Xcel-tronix, Inc. for possible warranty se
26 2) Unit beeps three times? Yes- Unit has been pro-grammed with this I-button key code. Go to Step 9 No- Go
28 FAQ 1. Can I have my unit professionally installed? Xceltronix, Inc. is partnering with local professional garage door insta
29 6. Do I have to install the disable button? Yes, while the unit will work without the disable button installed, it is needed to re-enable the syst
3 INTRODUCTION Congratulations on your purchase of an Autocloser automatic garage door closer. We are certain that this little black box will give you
4 this is intended to increase the safety of the system, these features are not intended to nor do they replace the auto reversing safety features tha
5 TOOLS RECOMMENDED PARTS LIST Item Description 1) 1 terminal wire 2ft. 2) 1 Disable wire 25 ft. 3) 1 Disable button 4)
6 PARTS IDENTIFICATION www.ActiveForever.com
7 INSTALLATION OF Autocloser HARDWARE RNING !!! To reduce the risk of severe injury or death: Read all instructions before installing. 1. Instal
8 1b. Attach reflective conspicuity tape to reflector plate. Peel off adhesive backing from the conspicuity tape and affix to side
9 2. Connect power to the Autocloser. The Autocloser uses a 110 Volt AC / DC power adapter. Attach each power wire to one of the screw terminals on
Kommentare zu diesen Handbüchern